--- /dev/null
+##############################################################################
+# QUICK-START
+#
+# The quickest start is if you want to use DHCP.
+# In that case, everything should work out of the box, no configuration
+# necessary, though the startup script will warn you that you haven't
+# specified anything.
+
+# WARNING :- some examples have a mixture of IPv4 (ie 192.168.0.1) and IPv6
+# (ie 4321:0:1:2:3:4:567:89ab) internet addresses. They only work if you have
+# the relevant kernel option enabled. So if you don't have an IPv6 enabled
+# kernel then remove the IPv6 address from your config.
+
+# If you want to use a static address or use DHCP explicitly, jump
+# down to the section labeled INTERFACE HANDLERS.
+#
+# If you want to do anything more fancy, you should take the time to
+# read through the rest of this file.
+
+
+##############################################################################
+# MODULES
+#
+# We now support modular networking scripts which means we can easily
+# add support for new interface types and modules while keeping
+# compatibility with existing ones.
+#
+# Modules load by default if the package they need is installed. If
+# you specify a module here that doesn't have its package installed
+# then you get an error stating which package you need to install.
+# Ideally, you only use the modules setting when you have two or more
+# packages installed that supply the same service.
+#
+# In other words, you probably should DO NOTHING HERE...
+
+# Prefer ifconfig over iproute2
+#modules="ifconfig"
+
+# You can also specify other modules for an interface
+# In this case we prefer udhcpc over dhcpcd
+#modules_eth0="udhcpc"
+
+# You can also specify which modules not to use - for example you may be
+# using a supplicant or linux-wlan-ng to control wireless configuration but
+# you still want to configure network settings per SSID associated with.
+#modules="!iwconfig !wpa_supplicant"
+# IMPORTANT: If you need the above, please disable modules in that order
+
+
+##############################################################################
+# INTERFACE HANDLERS
+#
+# We provide two interface handlers presently: ifconfig and iproute2.
+# You need one of these to do any kind of network configuration.
+# For ifconfig support, emerge sys-apps/net-tools
+# For iproute2 support, emerge sys-apps/iproute2
+
+# If you don't specify an interface then we prefer iproute2 if it's installed
+# To prefer ifconfig over iproute2
+#modules="ifconfig"
+
+# For a static configuration, use something like this
+# (They all do exactly the same thing btw)
+#config_eth0="192.168.0.2/24"
+#config_eth0="192.168.0.2 netmask 255.255.255.0"
+
+# If you need more than one address, you can use something like this
+# NOTE: ifconfig creates an aliased device for each extra IPv4 address
+# (eth0:1, eth0:2, etc)
+# iproute2 does not do this as there is no need to
+# WARNING: You cannot mix multiple addresses on a line with other parameters!
+#config_eth0="192.168.0.2/24 192.168.0.3/24 192.168.0.4/24"
+# However, that only works with CIDR addresses, so you can't use netmask.
+
+# You can also use IPv6 addresses
+# (you should always specify a prefix length with IPv6 here)
+#config_eth0="192.168.0.2/24 4321:0:1:2:3:4:567:89ab/64 4321:0:1:2:3:4:567:89ac/64"
+
+# If you wish to keep existing addresses + routing and the interface is up,
+# you can specify a noop (no operation). If the interface is down or there
+# are no addresses assigned, then we move onto the next step (default dhcp)
+# This is useful when configuring your interface with a kernel command line
+# or similar
+#config_eth0="noop 192.168.0.2/24"
+
+# If you don't want ANY address (only useful when calling for advanced stuff)
+#config_eth0="null"
+
+# If you need to pass parameters to go with an address, you can do so on the
+# same line as the address. You should split multiple addresses with newlines.
+# WARNING: You cannot mix multiple addresses on a line with other parameters!
+#config_eth0="192.168.0.2/24 scope host"
+#config_eth0="4321:0:1:2:3:4:567:89ab/64 nodad home preferred_lft 0"
+#config_eth0="192.168.0.2/24 scope host
+#4321:0:1:2:3:4:567:89ab/64 nodad home preferred_lft 0"
+
+# Here's how to do routing if you need it
+# We add an IPv4 default route, IPv4 subnet route and an IPv6 unicast route
+#routes_eth0="default via 192.168.0.1
+#10.0.0.0/8 via 192.168.0.1
+#::/0"
+
+# If a specified module fails (like dhcp - see below), you can specify a
+# fallback like so
+#fallback_eth0="192.168.0.2/24"
+#fallback_routes_eth0="default via 192.168.0.1"
+
+# NOTE: fallback entry must match the entry location in config_eth0
+# As such you can only have one fallback route.
+# Also, if you do not set a fallback_routes entry for an interface, the
+# routes entry will be used if that is set.
+
+# Some users may need to alter the MTU - here's how
+#mtu_eth0="1500"
+# Same for TX Queue Length
+#txqueuelen_eth0="1000"
+
+# Each module described below can set a default base metric, lower is
+# preferred over higher. This is so we can prefer a wired route over a
+# wireless route automatically. You can override this by setting
+#metric_eth0="100"
+# or on a global basis
+#metric="100"
+# The only downside of the global setting is that you have to ensure that
+# there are no conflicting routes yourself. For users with large routing
+# tables you may have to set a global metric as the due to a simple read of
+# the routing table taking over a minute at a time.
+
+# You may wish to disable the interface being brought down when stopping.
+# This is only of use for WakeOnLan.
+#ifdown_eth0="NO"
+
+##############################################################################
+# OPTIONAL MODULES
+
+#-----------------------------------------------------------------------------
+# WIRELESS (802.11 support)
+# Wireless can be provided by iwconfig or wpa_supplicant
+# wpa_supplicant is preferred, use the modules directive to prefer iwconfig.
+#modules="iwconfig"
+#
+# iwconfig
+# emerge net-wireless/wireless-tools
+###############################################
+# HINTS
+#
+# Most users will just need to set the following options
+# key_SSID1="s:yourkeyhere enc open" # s: means a text key
+# key_SSID2="aaaa-bbbb-cccc-dd" # no s: means a hex key
+# preferred_aps="'SSID 1' 'SSID 2'"
+#
+# Clear? Good. Now configure your wireless network below
+
+###############################################
+# SETTINGS
+# Hard code an SSID to an interface - leave this unset if you wish the driver
+# to scan for available Access Points
+# Set to "any" to connect to any SSID - the driver picks an Access Point
+# This needs to be done when the driver doesn't support scanning
+# This may work for drivers that don't support scanning but you need automatic
+# AP association
+# I would only set this as a last resort really - use the preferred_aps
+# setting at the bottom of this file
+
+# However, using ad-hoc (without scanning for APs) and master mode
+# do require the SSID to be set - do this here
+#essid_eth0="any"
+
+# Set the mode of the interface (managed, ad-hoc, master or auto)
+# The default is auto
+# If it's ad-hoc or master you also may need to specify the channel below
+#mode_eth0="auto"
+
+# If managed mode fails, drop to ad-hoc mode with the below SSID?
+#adhoc_essid_eth0="WLAN"
+
+# Some drivers/hardware don't scan all that well. We have no control over this
+# but we can say how many scans we want to do to try and get a better sweep of
+# the area. The default is 1.
+#scans_eth0="1"
+
+#Channel can be set (1-14), but defaults to 3 if not set.
+#
+# The below is taken verbatim from the BSD wavelan documentation found at
+# http://www.netbsd.org/Documentation/network/wavelan.html
+# There are 14 channels possible; We are told that channels 1-11 are legal for
+# North America, channels 1-13 for most of Europe, channels 10-13 for France,
+# and only channel 14 for Japan. If in doubt, please refer to the documentation
+# that came with your card or access point. Make sure that the channel you
+# select is the same channel your access point (or the other card in an ad-hoc
+# network) is on. The default for cards sold in North America and most of Europe
+# is 3; the default for cards sold in France is 11, and the default for cards
+# sold in Japan is 14.
+#channel_eth0="3"
+
+# Setup any other config commands. This is basically the iwconfig argument
+# without the iwconfig $iface.
+#iwconfig_eth0=""
+
+# Set private driver ioctls. This is basically the iwpriv argument without
+# the iwpriv $iface. If you use the rt2500 driver (not the rt2x00 one) then
+# you can set WPA here, below is an example.
+#iwpriv_eth0=""
+#iwpriv_SSID="set AuthMode=WPAPSK
+#set EncrypType=TKIP
+#set WPAPSK=yourpasskey"
+#NOTE: Even though you can use WPA like so, you may have to set a WEP key
+#if your driver claims the AP is encrypted. The WEP key itself will not be
+#used though.
+
+# Seconds to wait before scanning
+# Some drivers need to wait until they have finished "loading"
+# before they can scan - otherwise they error and claim that they cannot scan
+# or resource is unavailable. The default is to wait zero seconds
+#sleep_scan_eth0="1"
+
+# Seconds to wait until associated. The default is to wait 10 seconds.
+# 0 means wait indefinitely. WARNING: this can cause an infinite delay when
+# booting.
+#associate_timeout_eth0="5"
+
+# By default a successful association in Managed mode sets the MAC
+# address of the AP connected to. However, some drivers (namely
+# the ipw2100) don't set an invalid MAC address when association
+# fails - so we need to check on link quality which some drivers
+# don't report properly either.
+# So if you have connection problems try flipping this setting
+# Valid options are MAC, quality and all - defaults to MAC
+#associate_test_eth0="MAC"
+
+# Some driver/card combinations need to scan in Ad-Hoc mode
+# After scanning, the mode is reset to the one defined above
+#scan_mode_eth0="Ad-Hoc"
+
+# Below you can define private ioctls to run before and after scanning
+# Format is the same as the iwpriv_eth0 above
+# This is needed for the HostAP drivers
+#iwpriv_scan_pre_eth0="'host_roaming 2'"
+#iwpriv_scan_post_eth0="'host_roaming 0'"
+
+# Define a WEP key per SSID or MAC address (of the AP, not your card)
+# The encryption type (open or restricted) must match the
+# encryption type on the Access Point
+# You can't use "any" for an SSID here
+#key_SSID="1234-1234-1234-1234-1234-1234-56"
+# or you can use strings. Passphrase IS NOT supported
+# To use a string, prefix it with s:
+# Note - this example also sets the encryption method to open
+# which is regarded as more secure than restricted
+#key_SSID="s:foobar enc open"
+#key_SSID="s:foobar enc restricted"
+
+# If you have whitespace in your key, here's how to set it and use other
+# commands like using open encryption.
+#key_SSID="s:'foo bar' enc open"
+
+# WEP key for the AP with MAC address 001122334455
+#mac_key_001122334455="s:foobar"
+
+# Here are some more examples of keys as some users find others work
+# and some don't where they should all do the same thing
+#key_SSID="open s:foobar"
+#key_SSID="open 1234-5678-9012"
+#key_SSID="s:foobar enc open"
+#key_SSID="1234-5678-9012 enc open"
+
+# You may want to set multiple keys - here's an example
+# It sets 4 keys on the card and instructs to use key 2 by default
+#key_SSID="[1] s:passkey1 key [2] s:passkey2 key [3] s:passkey3 key [4] s:passkey4 key [2]"
+
+# You can also override the interface settings found in /etc/conf.d/net
+# per SSID - which is very handy if you use different networks a lot
+#config_SSID="dhcp"
+#dhcpcd_SSID="-t 5"
+#routes_SSID=
+#fallback_SSID=
+
+# Setting name/domain server causes /etc/resolv.conf to be overwritten
+# Note that if DHCP is used, and you want this to take precedence then
+# please put -R in your dhcpcd options
+#dns_servers_SSID="192.168.0.1 192.168.0.2"
+#dns_domain_SSID="some.domain"
+#dns_search_SSID="search.this.domain search.that.domain"
+# Please check the man page for resolv.conf for more information
+# as domain and search (searchdomains) are mutually exclusive and
+# searchdomains takes precedence
+
+# You can also set any of the /etc/conf.d/net variables per MAC address
+# incase you use Access Points with the same SSID but need different
+# networking configs. Below is an example - of course you use the same
+# method with other variables
+#config_001122334455="dhcp"
+#dhcpcd_001122334455="-t 10"
+#dns_servers_001122334455="192.168.0.1 192.168.0.2"
+
+# Map a MAC address to an SSID
+# This is used when the Access Point is not broadcasting its SSID
+# WARNING: This will override the SSID being broadcast due to some
+# Access Points sending an SSID even when they have been configured
+# not to!
+# Change 001122334455 to the MAC address and SSID to the SSID
+# it should map to
+#mac_essid_001122334455="SSID"
+
+# This lists the preferred SSIDs to connect to in order
+# SSID's can contain any characters here as they must match the broadcast
+# SSID exactly.
+# Surround each SSID with the " character and separate them with a space
+# If the first SSID isn't found then it moves onto the next
+# If this isn't defined then it connects to the first one found
+#preferred_aps="SSID1 SSID2"
+
+# You can also define a preferred_aps list per interface
+#preferred_aps_eth0="SSID3 SSID4"
+
+# You can also say whether we only connect to preferred APs or not
+# Values are "any", "preferredonly", "forcepreferred", "forcepreferredonly" and "forceany"
+# "any" means it will connect to visible APs in the preferred list and then any
+# other available AP
+# "preferredonly" means it will only connect to visible APs in the preferred list
+# "forcepreferred" means it will forcibly connect to APs in order if it does not find
+# them in a scan
+# "forcepreferredonly" means it forcibly connects to the APs in order and does not bother
+# to scan
+# "forceany" does the same as forcepreferred + connects to any other available AP
+# Default is "any"
+#associate_order="any"
+#associate_order_eth0="any"
+
+# You can define blacklisted Access Points in the same way
+#blacklist_aps="SSID1 SSID2"
+#blacklist_aps_eth0="SSID3 SSID4"
+
+# If you have more than one wireless card, you can say if you want
+# to allow each card to associate with the same Access Point or not
+# Values are "yes" and "no"
+# Default is "yes"
+#unique_ap="yes"
+#unique_ap_eth0="yes"
+
+# IMPORTANT: preferred_only, blacklisted_aps and unique_ap only work when
+# essid_eth0 is not set and your card is capable of scanning
+
+# NOTE: preferred_aps list ignores blacklisted_aps - so if you have
+# the same SSID in both, well, you're a bit silly :p
+
+
+############################################################
+# wpa_supplicant
+# emerge net-wireless/wpa_supplicant
+# Wireless options are held in /etc/wpa_supplicant/wpa_supplicant.conf
+# Consult the wpa_supplicant.conf.example that is installed in
+# /usr/share/doc/wpa_supplicant
+# To configure wpa_supplicant
+#wpa_supplicant_ath0="-Dmadwifi" # For Atheros based cards
+# Consult wpa_supplicant for more drivers - the default is -Dwext which should
+# work for most cards.
+
+# By default we don't wait for wpa_supplicant to associate and authenticate.
+# If you need to change this behaviour then you don't know how our scripts work
+# and setting this value could cause strange things to happen.
+# If you would like it to wait, you can specify how long in seconds.
+#associate_timeout_eth0=60
+# A value of 0 means wait forever.
+
+# You can also override any settings found here per SSID - which is very
+# handy if you use different networks a lot. See below for using the SSID
+# in our variables
+#config_SSID="dhcp"
+# See the System module below for setting dns/nis/ntp per SSID
+
+# You can also override any settings found here per MAC address of the AP
+# in case you use Access Points with the same SSID but need different
+# networking configs. Below is an example - of course you use the same
+# method with other variables
+#mac_config_001122334455="dhcp"
+#mac_dns_servers_001122334455="192.168.0.1 192.168.0.2"
+
+# When an interface has been associated with an Access Point, a global
+# variable called SSID is set to the Access Point's SSID for use in the
+# pre/post user functions below (although it's not available in preup as you
+# won't have associated then)
+
+# If you're using anything else to configure wireless on your interface AND
+# you have installed wpa_supplicant, you need to disable wpa_supplicant
+#modules="!iwconfig !wpa_supplicant"
+#or
+#modules="!wireless"
+
+##############################################################################
+# WIRELESS SSID IN VARIABLES
+##############################################################################
+# Remember to change SSID to your SSID.
+# Say that your SSID is My NET - the line
+# #key_SSID="s:passkey"
+# becomes
+# #key_My_NET="s:passkey"
+# Notice that the space has changed to an underscore - do the same with all
+# characters not in a-z A-Z (English alphabet) 0-9. This only applies to
+# variables and not values.
+#
+# Any SSID's in values like essid_eth0="My NET" may need to be escaped
+# This means placing the character \ before the character
+# \" need to be escaped for example
+# So if your SSID is
+# My "\ NET
+# it becomes
+# My \"\\ NET
+# for example
+# #essid_eth0="My\"\\NET"
+#
+# So using the above we can use
+# #dns_domain_My____NET="My\"\\NET"
+# which is an invalid dns domain, but shows the how to use the variable
+# structure
+#########################################################
+
+
+#-----------------------------------------------------------------------------
+# DHCP
+# DHCP can be provided by dhclient, dhcpcd, pump or udhcpc.
+#
+# dhclient: emerge net-misc/dhcp
+# dhcpcd: emerge net-misc/dhcpcd
+# pump: emerge net-misc/pump
+# udhcpc: emerge sys-apps/busybox
+
+# If you have more than one DHCP client installed, you need to specify which
+# one to use - otherwise we default to dhcpcd if available.
+#modules="dhclient" # to select dhclient over dhcpcd
+#
+# Notes:
+# - All clients send the current hostname to the DHCP server by default
+# - dhcpcd does not daemonize when the lease time is infinite
+# - udhcp-0.9.3-r3 and earlier do not support getting NTP servers
+# - pump does not support getting NIS servers
+# - DHCP tends to erase any existing device information - so add
+# static addresses after dhcp if you need them
+# - dhclient and udhcpc can set other resolv.conf options such as "option"
+# and "sortlist"- see the System module for more details
+
+# Regardless of which DHCP client you prefer, you configure them the
+# same way using one of following depending on which interface modules
+# you're using.
+#config_eth0="dhcp"
+
+# For passing custom options to dhcpcd use something like the following. This
+# example reduces the timeout for retrieving an address from 60 seconds (the
+# default) to 10 seconds.
+#dhcpcd_eth0="-t 10"
+
+# dhclient, udhcpc and pump don't have many runtime options
+# You can pass options to them in a similar manner to dhcpcd though
+#dhclient_eth0="..."
+#udhcpc_eth0="..."
+#pump_eth0="..."
+
+# GENERIC DHCP OPTIONS
+# Set generic DHCP options like so
+#dhcp_eth0="release nodns nontp nonis nogateway nosendhost"
+
+# This tells the dhcp client to release its lease when it stops, not to
+# overwrite dns, ntp and nis settings, not to set a default route and not to
+# send the current hostname to the dhcp server and when it starts.
+# You can use any combination of the above options - the default is not to
+# use any of them.
+
+#-----------------------------------------------------------------------------
+# For APIPA support, emerge net-misc/iputils or net-analyzer/arping
+
+# APIPA is a module that tries to find a free address in the range
+# 169.254.0.0-169.254.255.255 by arping a random address in that range on the
+# interface. If no reply is found then we assign that address to the interface
+
+# This is only useful for LANs where there is no DHCP server and you don't
+# connect directly to the internet.
+#config_eth0="dhcp"
+#fallback_eth0="apipa"
+
+#-----------------------------------------------------------------------------
+# ARPING Gateway configuration
+# and
+# Automatic Private IP Addressing (APIPA)
+# For arpingnet / apipa support, emerge net-misc/iputils or net-analyzer/arping
+#
+# This is a module that tries to find a gateway IP. If it exists then we use
+# that gateways configuration for our own. For the configuration variables
+# simply ensure that each octet is zero padded and the dots are removed.
+# Below is an example.
+#
+#gateways_eth0="192.168.0.1 10.0.0.1"
+#config_192168000001="192.168.0.2/24"
+#routes_192168000001="default via 192.168.0.1"
+#dns_servers_192168000001="192.168.0.1"
+#config_010000000001="10.0.0.254/8"
+#routes_010000000001="default via 10.0.0.1"
+#dns_servers_010000000001="10.0.0.1"
+
+# We can also specify a specific MAC address for each gateway if different
+# networks have the same gateway.
+#gateways_eth0="192.168.0.1,00:11:22:AA:BB:CC 10.0.0.1,33:44:55:DD:EE:FF"
+#config_192168000001_001122AABBCC="192.168.0.2/24"
+#routes_192168000001_001122AABBCC="default via 192.168.0.1"
+#dns_servers_192168000001_001122AABBCC="192.168.0.1"
+#config_010000000001_334455DDEEFF="10.0.0.254/8"
+#routes_010000000001_334455DDEEFF="default via 10.0.0.1"
+#dns_servers_010000000001_334455DDEEFF="10.0.0.1"
+
+# If you need to spoof the source address, you can add that as third parameter
+# like so
+#gateways_eth0="192.168.0.1,00:11:22:AA:BB:CC,192.168.0.50"
+#or
+#gateways_eth0="192.168.0.1,,192.168.0.50"
+# This requires arping to be installed though
+
+# If we don't find any gateways (or there are none configured) then we try and
+# use APIPA to find a free address in the range 169.254.0.0-169.254.255.255
+# by arping a random address in that range on the interface. If no reply is
+# found then we assign that address to the interface.
+
+# This is only useful for LANs where there is no DHCP server.
+#config_eth0="arping"
+
+# or if no DHCP server can be found
+#config_eth0="dhcp"
+#fallback_eth0="arping"
+
+# NOTE: We default to sleeping for 1 second the first time we attempt an
+# arping to give the interface time to settle on the LAN. This appears to
+# be a good default for most instances, but if not you can alter it here.
+#arping_sleep=5
+#arping_sleep_lan=7
+
+# NOTE: We default to waiting 3 seconds to get an arping response. You can
+# change the default wait like so.
+#arping_wait=3
+#arping_wait_lan=2
+
+#-----------------------------------------------------------------------------
+# VLAN (802.1q support)
+# For VLAN support, emerge sys-apps/iproute2
+# The old vconfig based VLAN support is no longer available.
+
+# Specify the VLAN numbers for the interface like so
+# Please ensure your VLAN IDs are NOT zero-padded
+#vlans_eth0="1 2"
+
+# You may not want to assign an IP the the physical interface, but we still
+# need it up.
+#config_eth0="null"
+
+# You can also configure the VLAN - see for ip man page for more details
+# To change the vlan interface name. If not set, the standard "iface.vlanid"
+# will be used. This is the replacement for the old 'vconfig set_name_type'
+# functionality.
+#vlan1_name="vlan1"
+#vlan2_name="eth0.2"
+
+# The following shows the old set_name_type setting and what new option to set:
+# Using eth9 & VLAN VID 26 as an example.
+# VLAN_PLUS_VID vlan26_name="vlan0026"
+# VLAN_PLUS_VID_NO_PAD vlan26_name="vlan26"
+# DEV_PLUS_VID vlan26_name="eth9.0026"
+# DEV_PLUS_VID_NO_PAD vlan26_name="eth9.26"
+
+# Set the vlan flags
+#vlan1_flags="reorder_hdr off gvrp on loose_binding on"
+
+# Configure in/egress maps
+#vlan1_ingress="2:6 3:5"
+#vlan1_egress="1:2"
+
+#config_vlan1="172.16.3.1/23"
+#config_vlan2="172.16.2.1/23"
+
+# NOTE: Vlans can be configured with a . in their interface names
+# When configuring vlans with this name type, you need to replace . with a _
+#config_eth0.1="dhcp" - does not work
+#config_eth0_1="dhcp" - does work
+
+# NOTE: Vlans are controlled by their physical interface and not per vlan
+# This means you do not need to create init scripts in /etc/init.d for each
+# vlan, you must need to create one for the physical interface.
+# If you wish to control the configuration of each vlan through a separate
+# script then you need to do this.
+#vlan_start_eth0="no"
+
+# If you do the above then you may want to depend on eth0 like so
+# rc_need_vlan1="net.eth0"
+# NOTE: depend functions only work in /etc/conf.d/net
+# and not in profile configs such as /etc/conf.d/net.foo
+
+# MAC-VLAN support
+# The following configuration can be used to create a new interface 'macvlan0'
+# linked to 'eth0'
+#macvlan_macvlan0="eth0"
+
+# MAC-VLAN mode (private, vepa, bridge, passtru)
+#mode_macvlan0="private"
+
+# IP address, MAC address, ... are configured as a normal interface
+#config_macvlan0="192.168.20.20/24"
+#mac_macvlan0="00:50:06:20:20:20"
+
+#-----------------------------------------------------------------------------
+# Bonding
+# For link bonding/trunking on 2.4 kernels, or kernels without sysfs
+# emerge net-misc/ifenslave
+
+# To bond interfaces together
+#slaves_bond0="eth0 eth1 eth2"
+#config_bond0="null" # You may not want to assign an IP the the bond
+
+# You can also configure the bond here, which must be done via sysfs on 2.6
+# kernels or newer. See the kernel bonding documentation for a description of
+# these options.
+#arp_ip_target_bond0="+26.0.0.0"
+
+# If any of the slaves require extra configuration - for example wireless or
+# ppp devices - we need to depend function on the bonded interfaces
+#rc_need_bond0="net.eth0 net.eth1"
+
+
+#-----------------------------------------------------------------------------
+# Classical IP over ATM
+# For CLIP support emerge net-dialup/linux-atm
+
+# Ensure that you have /etc/atmsigd.conf setup correctly
+# Now setup each clip interface like so
+#clip_atm0="peer_ip [if.]vpi.vci [opts],"
+# where "peer_ip" is the IP address of a PVC peer (in case of an ATM connection
+# with your ISP, your only peer is usually the ISP gateway closest to you),
+# "if" is the number of the ATM interface which will carry the PVC, "vpi.vci"
+# is the ATM VC address, and "opts" may optionally specify VC parameters like
+# qos, pcr, and the like (see "atmarp -s" for further reference). Please also
+# note quoting: it is meant to distinguish the VCs you want to create. You may,
+# in example, create an atm0 interface to more peers, like this:
+#clip_atm0="1.1.1.254,0.8.35 1.1.1.253,1.8.35"
+
+# By default, the PVC will use the LLC/SNAP encapsulation. If you rather need a
+# null encapsulation (aka "VC mode"), please add the keyword "null" to opts.
+
+
+#-----------------------------------------------------------------------------
+# PPP
+# For PPP support, emerge net-dialup/ppp
+# PPP is used for most dialup connections, including ADSL.
+# The older ADSL module is documented below, but you are encouraged to try
+# this module first.
+#
+# You need to create the PPP net script yourself. Make it like so
+#ln -s net.lo /etc/init.d/net.ppp0
+#
+# Each PPP interface requires an interface to use as a "Link"
+#link_ppp0="/dev/ttyS0" # Most PPP links will use a serial port
+#link_ppp0="eth0" # PPPoE requires an ethernet interface
+#link_ppp0="[itf.]vpi.vci" # PPPoA requires the ATM VC's address
+#link_ppp0="/dev/null" # ISDN links should have this
+#link_ppp0="pty 'your_link_command'" # PPP links over ssh, rsh, etc
+#
+# Here you should specify what pppd plugins you want to use
+# Available plugins are: pppoe, pppoa, capi, dhcpc, minconn, radius,
+# radattr, radrealms and winbind
+#plugins_ppp0="pppoe" # Required plugin for PPPoE
+#plugins_ppp0="pppoa vc-encaps" # Required plugin for PPPoA with an option
+#plugins_ppp0="capi" # Required plugin for ISDN
+#
+# PPP requires at least a username. You can optionally set a password here too
+# If you don't, then it will use the password specified in /etc/ppp/*-secrets
+# against the specified username
+#username_ppp0='user'
+#password_ppp0='password'
+# NOTE: You can set a blank password like so
+#password_ppp0=
+#
+# The PPP daemon has many options you can specify - although there are many
+# and may seem daunting, it is recommended that you read the pppd man page
+# before enabling any of them
+#pppd_ppp0="
+# maxfail 0 # WARNING: It's not recommended you use this
+# # if you don't specify maxfail then we assume 0
+# updetach # If not set, "/etc/init.d/net.ppp0 start" will return
+# # immediately, without waiting the link to come up
+# # for the first time.
+# # Do not use it for dial-on-demand links!
+# debug # Enables syslog debugging
+# noauth # Do not require the peer to authenticate itself
+# defaultroute # Make this PPP interface the default route
+# usepeerdns # Use the DNS settings provided by PPP
+#
+# On demand options
+# demand # Enable dial on demand
+# idle 30 # Link goes down after 30 seconds of inactivity
+# 10.112.112.112:10.112.112.113 # Phony IP addresses
+# ipcp-accept-remote # Accept the peers idea of remote address
+# ipcp-accept-local # Accept the peers idea of local address
+# holdoff 3 # Wait 3 seconds after link dies before re-starting
+#
+# Dead peer detection
+# lcp-echo-interval 15 # Send a LCP echo every 15 seconds
+# lcp-echo-failure 3 # Make peer dead after 3 consecutive
+# # echo-requests
+#
+# Compression options - use these to completely disable compression
+# noaccomp noccp nobsdcomp nodeflate nopcomp novj novjccomp
+#
+# Dial-up settings
+# lock # Lock serial port
+# 115200 # Set the serial port baud rate
+# modem crtscts # Enable hardware flow control
+# 192.168.0.1:192.168.0.2 # Local and remote IP addresses
+#"
+#
+# Dial-up PPP users need to specify at least one telephone number
+#phone_number_ppp0="12345689" # Maximum 2 phone numbers are supported
+# They will also need a chat script - here's a good one
+#chat_ppp0="
+#ABORT BUSY
+#ABORT ERROR
+#ABORT 'NO ANSWER'
+#ABORT 'NO CARRIER'
+#ABORT 'NO DIALTONE'
+#ABORT 'Invalid Login'
+#ABORT 'Login incorrect'
+#TIMEOUT 5
+#'' ATZ
+#OK AT # Put your modem initialization string here
+#OK 'ATDT\T'
+#TIMEOUT 60
+#CONNECT ''
+#TIMEOUT 5
+#~-- ''
+#"
+
+# If the link require extra configuration - for example wireless or
+# RFC 268 bridge - we need to depend on the bridge so they get
+# configured correctly.
+#rc_need_ppp0="net.nas0"
+
+#WARNING: if MTU of the PPP interface is less than 1500 and you use this
+#machine as a router, you should add the following rule to your firewall
+#
+#iptables -I FORWARD 1 -p tcp --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu
+
+#-----------------------------------------------------------------------------
+# ADSL
+# For ADSL support, emerge net-dialup/rp-pppoe
+# WARNING: This ADSL module is being deprecated in favour of the PPP module
+# above.
+# You should make the following settings and also put your
+# username/password information in /etc/ppp/pap-secrets
+
+# Configure the interface to use ADSL
+#config_eth0="adsl"
+
+# You probably won't need to edit /etc/ppp/pppoe.conf if you set this
+#adsl_user_eth0="my-adsl-username"
+
+#-----------------------------------------------------------------------------
+# ISDN
+# For ISDN support, emerge net-dialup/isdn4k-utils
+# You should make the following settings and also put your
+# username/password information in /etc/ppp/pap-secrets
+
+# Configure the interface to use ISDN
+#config_ippp0="dhcp"
+# It's important to specify dhcp if you need it!
+#config_ippp0="192.168.0.1/24"
+# Otherwise, you can use a static IP
+
+# NOTE: The interface name must be either ippp or isdn followed by a number
+
+# You may need this option to set the default route
+#ipppd_eth0="defaultroute"
+
+#-----------------------------------------------------------------------------
+# MAC changer
+# To set a specific MAC address
+#mac_eth0="00:11:22:33:44:55"
+
+# For changing MAC addresses using the below, emerge net-analyzer/macchanger
+# - to randomize the last 3 bytes only
+#mac_eth0="random-ending"
+# - to randomize between the same physical type of connection (e.g. fibre,
+# copper, wireless) , all vendors
+#mac_eth0="random-samekind"
+# - to randomize between any physical type of connection (e.g. fibre, copper,
+# wireless) , all vendors
+#mac_eth0="random-anykind"
+# - full randomization - WARNING: some MAC addresses generated by this may NOT
+# act as expected
+#mac_eth0="random-full"
+# custom - passes all parameters directly to net-analyzer/macchanger
+#mac_eth0="some custom set of parameters"
+
+# You can also set other options based on the MAC address of your network card
+# Handy if you use different docking stations with laptops
+#config_001122334455="dhcp"
+
+#-----------------------------------------------------------------------------
+# TUN/TAP
+# For TUN/TAP support install iproute2, openvpn or usermode-utilities
+#
+# You must specify if we're a tun or tap device. Then you can give it any
+# name you like - such as vpn
+#tuntap_vpn="tun"
+#config_vpn="192.168.0.1/24"
+
+# Or stick wit the generic names - like tap0
+#tuntap_tap0="tap"
+#config_tap0="192.168.0.1/24"
+
+# Use something like this to pass custom options to iproute2 during
+# tunnel creation. This sets the user and group ownership of the node.
+#iproute2_tun1="user foo group bar"
+# For passing custom options to tunctl use something like the following. This
+# example sets the owner to adm
+#tunctl_tun1="-u adm"
+# OpenVPN-2.1_rc6 and newer allow --user and --group to set owner and group
+# of the node as well
+#openvpn_tun1="--user foo --group bar"
+
+#-----------------------------------------------------------------------------
+# Bridging (802.1d)
+# For bridging support emerge net-misc/bridge-utils
+
+# To add ports to bridge br0
+#bridge_br0="eth0 eth1"
+# or dynamically add them when the interface comes up
+#bridge_add_eth0="br0"
+#bridge_add_eth1="br0"
+
+# NOTE: If you want to manually start an empty bridge, and then dynamically add
+# ports to it you must set at least one of the following variables based on the
+# interface name, so that we can pick it up from your configuration. Even an
+# empty value variable is fine, but at least one of them must be set:
+# brctl_IFVAR
+
+# You need to configure the ports to null values so dhcp does not get started
+#config_eth0="null"
+#config_eth1="null"
+
+# Finally give the bridge an address - dhcp or a static IP, this is assigned to
+# the bridge when the bridge is explicitly started.
+#config_br0="dhcp" # may not work when adding ports dynamically
+#config_br0="192.168.0.1/24"
+
+# If any of the ports require extra configuration - for example wireless or
+# ppp devices - we need to depend on them like so.
+#rc_need_br0="net.eth0 net.eth1"
+
+# Below is an example of configuring the bridge
+# Consult "man brctl" for more details
+#brctl_br0="setfd 15
+#sethello 2
+#stp on"
+
+# You can also configure the bridge or bridge members via sysfs on 2.6 kernels
+# or newer. See the kernel bridge documentation for a description of these
+# options.
+#stp_state_br0="0"
+#forward_delay_br0="10"
+#hairpin_mode_eth0="1"
+
+#-----------------------------------------------------------------------------
+# RFC 2684 Bridge Support
+# For RFC 2684 bridge support emerge net-misc/br2684ctl
+
+# Interface names have to be of the form nas0, nas1, nas2, etc.
+# You have to specify a VPI and VCI for the interface like so
+#br2684ctl_nas0="-a 0.38" # UK VPI and VCI
+
+# You may want to configure the encapsulation method as well by adding the -e
+# option to the command above (may need to be before the -a command)
+# -e 0 # LLC (default)
+# -e 1 # VC mux
+
+# Then you can configure the interface as normal
+#config_nas0="'192.168.0.1/24'"
+
+#-----------------------------------------------------------------------------
+# Tunneling
+# WARNING: For tunneling it is highly recommended that you
+# emerge sys-apps/iproute2
+#
+# For GRE tunnels
+#iptunnel_vpn0="mode gre remote 207.170.82.1 key 0xffffffff ttl 255"
+
+# For IPIP tunnels
+#iptunnel_vpn0="mode ipip remote 207.170.82.2 ttl 255"
+
+# To configure the interface
+#config_vpn0="192.168.0.2 pointopoint 192.168.1.2" # ifconfig style
+#config_vpn0="192.168.0.2 peer 192.168.1.1" # iproute2 style
+
+# 6to4 Tunnels allow IPv6 to work over IPv4 addresses, provided you
+# have a non-private address configured on an interface.
+# link_6to4="eth0" # Interface to base its addresses on
+# config_6to4="ip6to4"
+# You may want to depend on eth0 like so
+#rc_need_6to4="net.eth0"
+# To ensure that eth0 is configured before 6to4. Of course, the tunnel could be
+# any name and this also works for any configured interface.
+# NOTE: If you're not using iproute2 then your 6to4 tunnel has to be called
+# sit0 - otherwise use a different name like 6to4 in the example above.
+
+# You can also specify a relay and suffix if you like.
+# The default relay is 192.88.99.1 and the default suffix is :1
+#relay_6to4="192.168.3.2"
+#suffix_6to4=":ff"
+
+#-----------------------------------------------------------------------------
+# Advanced Routing
+# WARNING: For advanced routing you MUST be using sys-apps/iproute2
+#
+# This provides a means to do multi-homing and more using the Routing Policy
+# Database (RPDB).
+#
+# See the following links for background and more information.
+# http://linux-ip.net/html/ch-routing.html
+# http://linux-ip.net/html/ch-advanced-routing.html
+
+# The rules listed will be added with 'ip rule add LINE' when the interface is
+# being brought up. They will also be removed with 'ip rule delete LINE'.
+# The rules added are also stored for later removal, so if you alter your rules
+# directly before stopping, you should review your rules again after stopping.
+
+# Note in earlier versions of openrc, this was provided as an example in
+# postup/postdown, however that implementation suffered some bugs in corner
+# cases, which are now fixed with this merger. If you used the previous
+# example, you should only need to drop the relevent portions of your
+# postup/postdown functions, and review the quoting in your rules_IFACE
+# variables.
+
+# Below is a trivial example for a dual-homed connection where there is an OOB
+# management network. Only packets explicitly with an address from or to the
+# OOB are sent via eth0. All others go via eth1 as the eth1 rules have a lower
+# priority.
+
+# If you want to use names for your tables, you should put lines into
+# /etc/iproute2/rt_tables, an example follows:
+# 2 oob
+# 3 external
+#
+# IPv6 RPDB entries are to be found in the rules6_IFVAR variables:
+
+#rules_eth0="
+#from ZZZ.ZZZ.200.128/27 table oob priority 500
+#to ZZZ.ZZZ.200.128/27 table oob priority 550"
+#rules_eth1="
+#from XXX.XXX.112.0/24 table external priority 400
+#to XXX.XXX.112.0/24 table external priority 450"
+#routes_eth0="
+#ZZZ.ZZZ.200.128/27 dev eth0 table oob scope link
+#default via ZZZ.ZZZ.200.129 table oob"
+#routes_eth1="
+#XXX.XXX.112.0/24 dev eth1 table external scope link
+#default via XXX.XXX.112.1 dev eth1"
+
+# IPv6 example:
+#rules6_eth0="
+#from 2001:0DB8:AAAA:BBBB::/64 table vpn priority 100
+#to 2001:0DB8:AAAA:BBBB::/64 table vpn priority 150"
+
+
+#-----------------------------------------------------------------------------
+# System
+# For configuring system specifics such as domain, dns, ntp and nis servers
+# It's rare that you would need todo this, but you can anyway.
+# This is most benefit to wireless users who don't use DHCP so they can change
+# their configs based on SSID.
+
+# If you omit the _eth0 suffix, then it applies to all interfaces unless
+# overridden by the interface suffix.
+#dns_domain_eth0="your.domain"
+#dns_servers_eth0="192.168.0.2 192.168.0.3"
+#dns_search_eth0="this.domain that.domain"
+#dns_options_eth0="timeout:1 rotate"
+#dns_sortlist_eth0="130.155.160.0/255.255.240.0 130.155.0.0"
+# See the man page for resolv.conf for details about the options and sortlist
+# directives
+
+#ntp_servers_eth0="192.168.0.2 192.168.0.3"
+
+#nis_domain_eth0="domain"
+#nis_servers_eth0="192.168.0.2 192.168.0.3"
+
+# NOTE: Setting any of these will stamp on the files in question. So if you
+# don't specify dns_servers but you do specify dns_domain then no nameservers
+# will be listed in /etc/resolv.conf even if there were any there to start
+# with.
+# If this is an issue for you then maybe you should look into a resolv.conf
+# manager like resolvconf-gentoo to manage this file for you. All packages
+# that baselayout supports use resolvconf-gentoo if installed.
+
+#-----------------------------------------------------------------------------
+# Cable in/out detection
+# Sometimes the cable is in, others it's out. Obviously you don't want to
+# restart net.eth0 every time when you plug it in either.
+#
+# netplug is a package that detects this and requires no extra configuration
+# on your part.
+# emerge sys-apps/netplug
+# or
+# emerge sys-apps/ifplugd
+# and you're done :)
+
+# By default we don't wait for netplug/ifplugd to configure the interface.
+# If you would like it to wait so that other services know that network is
+# up then you can specify a timeout here. A value of 0 means wait forever,
+# and a negative value means never wait.
+#plug_timeout_eth0="10"
+# If you want to set it for all interfaces:
+#plug_timeout="10"
+
+# If you don't want to use netplug on a specific interface but you have it
+# installed, you can disable it for that interface via the modules statement
+#modules_eth0="!netplugd"
+# You can do the same for ifplugd
+#
+# You can disable them both with the generic plug
+#modules_eth0="!plug"
+
+# To use specific ifplugd options, fex specifying wireless mode
+#ifplugd_eth0="--api-mode=wlan"
+# man ifplugd for more options
+
+#-----------------------------------------------------------------------------
+# Interface hardware tuning & configuration via ethtool
+# If you need to change explicit hardware settings on your network card prior
+# to bringing the interface up, the following is available.
+#
+# For a full listing of settings, please consulting ethtool(8) and the output
+# of "ethtool --help".
+#
+# Multiple entries (seperated by newlines) are supported in all of the
+# variables as some settings cannot be changed at the same time.
+#
+# Valid variable name fragments: change pause coalesce ring offload
+# change_eeprom identify nfc flash rxfh_indir ntuple
+
+# Set Wake-On-Lan to listen for SecureOn MagicPacket(tm), the message level to
+# notify us of WOL changes, and the SecureOn password to 'DE:AD:BE:EF:CA:FE'.
+#ethtool_change_eth0="wol gs
+#msglvl wol on
+#sopass DE:AD:BE:EF:CA:FE"
+
+# Disable pause auto-negotiation and explicitly enable RX and TX pause.
+#ethtool_pause_eth0="autoneg off
+#rx on tx on"
+
+# Enasble adaptive RX and TX coalescing
+#ethtool_coalesce_eth0="adaptive-rx on adaptive-tx on"
+
+# Change ring buffer settings
+#ethtool_ring_eth0=""
+
+# Enable all offload settings
+#ethtool_offload_eth0="rx on tx on sg on tso on ufo on gso on gro on lro on"
+
+# Change specific bytes in the EEPROM
+#ethtool_change_eeprom_eth0=""
+
+# Run the identify sequence on the interface for 1 second (does not return until completion)
+#ethtool_identify_eth0="1"
+
+# Configure receive network flow classification
+#ethtool_nfc_eth0="
+#rx-flow-hash tcp4 f
+#rx-flow-hash udp4 s"
+
+# Flash firmware to all regions
+#ethtool_flash_eth0="/some/path/firmware1 0"
+
+# Flash firmware to region 1
+#ethtool_flash_eth0="/some/path/firmware2 1"
+
+# Set receive flow hash indirection table for even balancing between N receive queues
+#ethtool_rxfh_indir_eth0="equal 4"
+
+# Configure Rx ntuple filters and actions
+#ethtool_ntuple_eth0=""
+
+# Additionally, there is a special control variable, if you need to change the
+# order of option processing. The default order is:
+# flash change-eeprom change pause coalesce ring offload identify nfc rxfh-indir ntuple
+
+# Set global order to default
+#ethtool_order="flash change-eeprom change pause coalesce ring offload identify nfc rxfh-indir ntuple"
+
+# Hypothetical network card that requires a change-eeprom toggle to enable flashing
+#ethtool_order_eth0="change-eeprom flash change pause coalesce ring offload nfc rxfh-indir ntuple"
+
+##############################################################################
+# ADVANCED CONFIGURATION
+#
+# Four functions can be defined which will be called surrounding the
+# start/stop operations. The functions are called with the interface
+# name first so that one function can control multiple adapters. An extra two
+# functions can be defined when an interface fails to start or stop.
+#
+# The return values for the preup and predown functions should be 0
+# (success) to indicate that configuration or deconfiguration of the
+# interface can continue. If preup returns a non-zero value, then
+# interface configuration will be aborted. If predown returns a
+# non-zero value, then the interface will not be allowed to continue
+# deconfiguration.
+#
+# The return values for the postup, postdown, failup and faildown functions are
+# ignored since there's nothing to do if they indicate failure.
+#
+# ${IFACE} is set to the interface being brought up/down
+# ${IFVAR} is ${IFACE} converted to variable name bash allows
+#
+# For historical and compatibility reasons, preup is actually normally called
+# in the following sequence: up ; preup ; up.
+# The first up causes the kernel to initialize the device, so
+# that it is available for use in the preup function. However, for some
+# hardware, e.g. CAN devices, some configuration is needed before trying to up
+# the interface will actually work. For such hardware, the
+# up_before_preup variables will allow skipping the first up call if set
+# to yes.
+#up_before_preup_IFVAR="NO"
+#up_before_preup="NO"
+
+#preup() {
+# # Test for link on the interface prior to bringing it up. This
+# # only works on some network adapters and requires the
+# # sys-apps/net-tools package to be installed.
+# if mii-tool "${IFACE}" 2> /dev/null | grep -q 'no link'; then
+# ewarn "No link on ${IFACE}, aborting configuration"
+# return 1
+# fi
+#
+# # Test for link on the interface prior to bringing it up. This
+# # only works on some network adapters and requires the ethtool
+# # package to be installed.
+# if ethtool "${IFACE}" | grep -q 'Link detected: no'; then
+# ewarn "No link on ${IFACE}, aborting configuration"
+# return 1
+# fi
+#
+# # Test to see if we're docked or not and configure like so
+# # config_docked="dhcp"
+# if grep -q "1" /sys/devices/platform/dock.0/docked; then
+# einfo "${IFACE} is docked - configuring"
+# _configure_variables "docked"
+# fi
+#
+# # Remember to return 0 on success
+# return 0
+#}
+
+#predown() {
+# # The default in the script is to test for NFS root and disallow
+# # downing interfaces in that case. Note that if you specify a
+# # predown() function you will override that logic. Here it is, in
+# # case you still want it...
+# if is_net_fs /; then
+# eerror "root filesystem is network mounted -- can't stop ${IFACE}"
+# return 1
+# fi
+#
+# # Remember to return 0 on success
+# return 0
+#}
+
+#postup() {
+# # This function could be used, for example, to register with a
+# # dynamic DNS service. Another possibility would be to
+# # send/receive mail once the interface is brought up.
+#}
+
+#postdown() {
+# # Enable Wake-On-LAN for every interface except for lo
+# # Probably a good idea to set ifdown="no" in /etc/conf.d/net
+# # as well ;)
+# [ "${IFACE}" != "lo" ] && ethtool -s "${IFACE}" wol g
+# # Return 0 always
+# return 0
+#}
+
+#failup() {
+# # This function is mostly here for completeness... I haven't
+# # thought of anything nifty to do with it yet ;-)
+#}
+
+#faildown() {
+# # This function is mostly here for completeness... I haven't
+# # thought of anything nifty to do with it yet ;-)
+#}
projects / config / samara / etc.git / commitdiff